Wichita Falls, TX · Free Repipe Assessment
Whole-Home Repiping in Wichita Falls, TX
When galvanized supply lines have corroded past section repair, or a polybutylene system has reached the end of its reliable life, a full repipe is the right call. We repipe in PEX or copper with minimal wall damage and a full pressure test before anything is closed up.
- PEX and copper repiping — sized for actual demand, not builder minimums
- Galvanized, polybutylene, and failing copper replacement
- Pressure-tested before drywall is closed; permits pulled where required
Direct answer
When does a home need a full repipe rather than section repairs?
A full repipe makes sense when galvanized steel supply lines have corroded to the point where pressure is low at every fixture and sediment has built up throughout the pipe walls — not just at one section. The same applies to polybutylene systems, installed in many homes through the 1990s, which have a documented pattern of fitting failure that cannot be repaired section by section. Three or more pinhole leaks in copper at different locations within a few years indicates the pipe wall has thinned enough that the next repair will not be the last. At that point, the cost of continued section repairs exceeds the cost of doing the whole job once.
Low pressure at every fixture, or recurring leaks?
Call (940) 905-8032. We assess the supply system, tell you honestly whether section repair or a full repipe is the better value, and give you a written quote for both paths so you can decide without pressure.
PEX vs copper
Which material is right for a Wichita Falls repipe?
PEX is the most common choice for full repipes in this area. It is flexible — fewer fittings, fewer potential leak points, and faster installation through existing wall cavities with less drywall damage. It is highly resistant to freeze damage because it expands rather than splitting. In Wichita Falls hard water, PEX does not scale or pit the way copper can over decades of exposure to mineral-heavy supply.
Copper is the right call where local code requires it, where the homeowner prefers a metallic supply system, or where sections are being matched to existing copper distribution. Copper carries more fittings through walls, costs more in materials and labour, but has a longer proven track record in any climate. Both materials, installed correctly and sized properly, will outlast the homes they are installed in. We match the recommendation to your situation and budget.
How it works
What a whole-home repipe actually involves
- 01
Assessment and written quote
We map the existing supply system, identify every fixture and hose bib, confirm material and sizing, and give you a written all-in price before any work is scheduled.
- 02
Permits pulled
Most whole-home repipes require a permit in Wichita Falls. We handle this — the permit is pulled before work starts, not after.
- 03
New lines run
Main shut-off closed. New lines run through wall cavities, attic, or crawlspace to each fixture group. Minimal drywall cuts — typically access panels at manifold locations and where turns cannot be made blind.
- 04
Connections made at fixtures
New shut-off valves at every fixture, braided flex connectors replaced, every toilet, sink, shower, tub, and hose bib reconnected and tested.
- 05
Pressure test
New supply pressurised and held. Every connection checked before drywall is patched or paint touched.
- 06
Inspection and old pipe removal
Where accessible, old galvanized or poly is removed. Where buried in slab or unreachable wall, it is capped and abandoned in place.
Signs you need a repipe
When section repairs are no longer the answer
- Low pressure at every fixture, not just one location
- Rust-coloured water when the cold side runs — not just the hot
- Three or more pinhole leaks repaired in the past two to three years
- Galvanized pipe confirmed — typically homes built before 1970
- Polybutylene pipe (grey plastic, marked PB) anywhere in the supply
- Recurring joint failures at different locations rather than one problem section
Timeline and disruption
What to expect during a repipe
- Most single-family homes repipe in one to three days. Larger homes or complex layouts take longer.
- Water is off during active work — typically six to eight hours per day. Supply is restored at the end of each workday.
- You do not need to leave the home. Most rooms remain fully accessible.
- Drywall patching is usually a separate trade. We give you a list of every access cut for your drywall contractor.
Pricing
What does a whole-home repipe cost in Wichita Falls?
A typical single-family home repipe (PEX, 3 bed / 2 bath, one story) runs $3,500–$5,500 including labour, materials, permit, and pressure testing. Two-story homes and those with additional bathrooms or complex layouts run $5,500–$8,500+. Copper adds to the material cost. Drywall repair is quoted separately. We give you an all-in written price after assessment — no surprises once work starts.
Service area
Repiping across Wichita Falls and the 940
FAQ
Repiping questions
Do I need to move out during a repipe?
Is PEX as good as copper?
Will my water pressure improve after a repipe?
How do I know if my home has galvanized or polybutylene pipe?
Related services
Also from Discount Plumbing TX
Pipe Repair
Section repair for accessible leaks, pinhole failures, and joint breaks where a full repipe is not yet warranted.
Learn moreLeak Detection
Acoustic and thermal leak location before repair — so we fix the right section.
Learn moreWater Pressure
Diagnosis and correction of low or fluctuating pressure — often the first symptom of a supply system problem.
Learn moreOne call ends it
Stop repairing the same pipes and repipe once
Assessment, written quote, permitted installation, pressure test before walls close. Call (940) 905-8032 and get a straight answer on whether a repipe is the right move for your home.
Call (940) 905-8032